RESUMEN
OBJECTIVES: The aim of this study was to investigate the bond strength of ceramic restorations luted using a self-adhesive resin cement (RelyX Unicem, 3M ESPE) under different dentin conditions. MATERIAL AND METHODS: In the experimental groups, ceramic restorations were luted to bovine incisors with RelyX Unicem under the following conditions: [Dry dentin]: surface was dried using air stream for 15 s; [Moist dentin]: excess dentin moisture was removed with absorbent paper; [Bonding agent]: Clearfil SE Bond (Kuraray) self-etching adhesive system was previously applied to dentin. In the Control group, cementation was done using an etch-and-rinse adhesive (Excite DSC) and Variolink II resin cement (Ivoclar Vivadent). Photoactivation of the resin cements was performed with UltraLume LED 5 unit (Ultradent). The restorations (n=5 per group) were sectioned into beams and microtensile testing was carried out. Data were subjected to ANOVA and Tukey's test (p<0.05). Failure modes were classifed under Scanning Electron Microscopic (SEM) (x120 magnifcation). RESULTS: The bond strength was dependent on the moisture status of the dentin. Bond strength in the "dry dentin group" was signifcantly lower than that of all other groups, which showed similar results. A predominance of mixed failures was detected for the control group, while a predominance of adhesive failures was observed for the "bonding agent" and "dry dentin" groups. The "moist dentin" group presented predominantly cohesive failures within the luting material. The previous application of a self-etching adhesive showed no signifcant effect. CONCLUSIONS: Only excess dentin moisture should be removed for the cementation of ceramic restorations with self-adhesive resin cements.
Asunto(s)
Animales , Bovinos , Cerámica/química , Restauración Dental Permanente , Recubrimiento Dental Adhesivo/métodos , Materiales Dentales/química , Dentina/ultraestructura , Cementos de Resina/química , Adhesividad , Aire , Grabado Ácido Dental/métodos , Silicatos de Aluminio/química , Cementación/métodos , Luces de Curación Dental/clasificación , Análisis del Estrés Dental , Desecación , Porcelana Dental/química , Ensayo de Materiales , Microscopía Electrónica de Rastreo , Metacrilatos/química , Distribución Aleatoria , Estrés Mecánico , Temperatura , Resistencia a la Tracción , Factores de Tiempo , Agua/químicaRESUMEN
Aim: To investigate the influence of deproteinization and moisture condition (wet vs. dry) on the bond strength and micromorphology of resin-dentin bonding interfaces. Methods: Dentin surfaces were etched with 37% phosphoric acid for 15 s and rinsed with water. Four groups (n = 10) were tested: WET: dentin was left visibly moist; DRY: dentin was dried with compressed air; WET-D: dentin was deproteinized for 60 s using 10% NaOCl solution and left moist; DRY-D: dentin was deproteinized and dried. Prime&Bond 2.1 adhesive was applied and the teeth were restored with composite resin. Microtensile test was carried out after 24 h, and failure modes classified under magnification. Data were subjected to two-way ANOVAand Tukeys test (P < 0.05). The bonding micromorphology was analyzed by confocal laser scanning microscopy. Results: The group DRY showed significantly lower bond strength (P < 0.05) than the other groups, which were similar to each other (P > 0.05). Adhesive failures were predominant. Analysis of micromorphology showed formation of a collagen-resin hybrid layer only for the non-deproteinizedgroups. Adhesive penetration into the dentinal tubules was deeper for the DRY-D compared to the WETD group. Conclusion: The bond strength was not dependent on the moisture condition and a more homogeneous hybridization was obtained when dentin was deproteinized.